ABSTRACT
The tremendous (large) demand of some petroleum fractions in our modern world
today has drive some professionals (experts) in oil sectors into exploration
and drilling operation which is aimed at locating the mineral oil deposit and
extracting it from beneath the earth surface with aid of some vital exploration
techniques and drilling machine (ng) on which drill string consisting of drill
pipe, drill rods, drill stem and drill bit are attached on it.
During drilling operations, a drill bit that is attached to along pieces of
hollow pipes called the drill string is used to drill the wells into the occan
floor. As the drill bit spirals its way down through the ground, crushing rocks
and stones as it goes, additional lengths of drill pipe are continuously added.
First, from the starter hole, they drill a surface hole down to a pre-set
depth, which is somewhere above where they think the oil trap is located.
There are five basic steps to drilling the surface hole.
1. place the drill bit, collar and drill pipe in
the hole.
2. attach the Kelly and turntable and begin drilling
3. as drilling progresses, circulate mud through
the pipe and out of the bit to float the rock cuttings out of the hole.
4. add new sections (joints) of drill pipe as the
hole gets deeper and finally, remove (tripout) the drill pipe collar and bit
when the preset depth is reached.
Once they reach the pre-set depth, they must run and cement the
casing by placing casing pipe section into the hole to prevent it from
collapsing on itself. The casing pipe has spacers around the outside to keep it
centered in the hole.
Drilling continues in stages; they
drill, then run and cement new casings, then drill again. When the rock
cuttings from the mud reveal the oil sand from the reservoir rock, this implies
the final depth reached.
At this point, they remove the drilling apparatus from the hole
and perform several test to conform this finding.
Once the final depth has reached,
the crew completes the well to allow oil to flow into the casing in a
controlled manner. First, they lower a perforating gun into the well to the
production depth. The gun has explosive charges to create holes in the casing
through which oil can flow. A small-diameter pipe after the casing has
been perforated is run into the hole as a conduit for oil and gas to flow up
the well.
A device termed packer is run down the outside of the tubing
finally, a multivalved structure called a Christmas tree is connected to
the top of the tubing and cement it to the top of the casing and thus,
Christmas tree allows for the control of oil flow from the well.
Once the well is completed, oil is
made to flow into the well for limestone reservoir rock, acid is pumped down
the well and out of the perforations and it dissolves channels in the limestone
that lead oil (into the well for sands tone reservoir rock, a specially blended
fluid containing proppants( sand, wallnutshell, alluminium pellets) is pumped
down the well and out the perforations and pressure from this fluid makes small
fractures in the sandstone that allow oil to flow into the well, prop pants
hold these fractures open.
Finally, once the oil is flowing,
the rig is removed from the site and production equipment is set up to extract
oil from the well.
TABLE OF CONTENT
CHAPTER ONE
INTRODUCTION
CHAPTER TWO
LITERATURE REVIEW
2.1
World crude
oil
2.2
Crude oil
exploration
2.3
Evaluation of oil well
2.4
Drilling process (drilling
methods)
2.5
Crude oil production (oil production methods)
CHAPTER THREE
DRILLING PROBLEMS AND ITS
SOLUTION
CHAPTER FOUR
DISCUSSION
CHAPTER FIVE
CONCLUSION/RECOMMENDATIONS
REFERENCES
(REFERENCES)
APPENDIX
NOMENCLATURES
(NOTATION)
CHAPTER ONE
INTRODUCTION
The crude oil is one of the natural
resources endowed to man on earth it is a complex and solid hydrocarbons
containing also traces of sulphur, nitrogen and oxygen. The crude oil
originates from dead remains of small, bigoquatic plant animals and terrestrial
plant which has been buried over many millions of years beneath the rock layers
and as a result of continuous heaping of masses of the mud, silt and other
sediments ones it and also by the active actions of bacterial and heat it is
hugely formed. This vital natural resources (crude oil) in Nigeria in past
decades was not known to man as a valuable substance.
Thus, the recent over demands for
some petroleum fractions as sources of heat and chemical energy and also and
raw material both in our homes, oil and gas industries today has continue to
drive some of the oil and gas industries all over the world to develop system
to reach the reservoirs beneath the earth surface.
Hence, the production of crude oil
which is by drilling process is a complex and sophisticated process used in
order to extract the oil in commercial quantity. This fact can never be over
emphasize with the contributions of the geologist and geophysicists. The
exploration of oil basin involves some geophysical techniques namely; magnetic
method, gravity method and seismography. They latter which is the most
important due to us ease in detecting the large oil basin is mainly used in oil
exploration.
Hence, also, the drilling of oil
well which commence after oil exploration and well testing involves use of a
complex machine term drill rig (machine) on which also drill pipe, drill bit
which aids the cutting, grinding of core formation under the surface (well) in
order to reach the reservoir is attach to a drill string (long length hollow
steel pipe on which drill collar is also mounted on). The drilling action by
the drill bit of the drill machine and its penetration speed depends on the
power supply to the machine and as well as the geological formation. The
economical use of some drilling process (technique) has aid a lot in commercial
crude oil production.
In Nigeria, precisely with the
development in the drilling technology and oil exploration for example, in
Niger-Delta areas, Kaduna and Port-Harcourt more competent, skill and
unskill labourers have today gain opportunity to secure jobs in the drilling
sectors of Nigeria and also some vital petroleum fractions example gasoline
(petro) are now today very much available at some places at good prices.
Drilling a well to extract crude
oil is a complicated process, but it is the only way to confirm the extent and
existence of the oil beneath the earth crust. After initial exploration in
activities sites preparation begins. The type of rig system to be used whether
rotary or cable, is determined when the drilled well is completed and turned
into a production facility. Capable of bringing a steady flow of oil to the
surface, usually for many years, while getting the oil out of the ground may
seen complicated, moving it from the point of production to the fuel consumer
is just as complex. Today, there are more than 200,000 miles of oil pipeline in
the U.S.
In 2000, total domestic crude oil
field production averaged 5,822,000 barrels per day. The top crude oil
producing states are Texas, California Louisiana etec.
Department | Chemical Engineering |
Project ID Code | CHE0025 |
Chapters | 5 Chapters |
No of Pages | 54 pages |
Methodology | Scientific Method |
Reference | YES |
Format | Microsoft Word |
Price | ₦4000, $15 |
|
|
Contact Us On | +2347043069458 |